Update notes: Motors changed to 9000KV and removed the Microphone since 2019-04-08
The Mobula7 HD comes with Runcam Split3-lite instead CaddxFVP Turtle v2 after Dec.30th 2020
The Mobula7 HD comes with Speki+ DSM2/DSMX receiver instead SP09 DSM2/DSMX receiver after Feb.1st 2021
Update log: This batch of Mobula7 HD comes with OPENVTX could support 400mw output from May.2022
Please use the following vtx table
vtxtable bands 6
vtxtable channels 8
vtxtable band 1 BOSCAM_A A FACTORY 5865 5845 5825 5805 5785 5765 5745 5725
vtxtable band 2 BOSCAM_B B FACTORY 5733 5752 5771 5790 5809 5828 5847 5866
vtxtable band 3 BOSCAM_E E FACTORY 5705 5685 5665 0 5885 5905 0 0
vtxtable band 4 FATSHARK F FACTORY 5740 5760 5780 5800 5820 5840 5860 5880
vtxtable band 5 RACEBAND R FACTORY 5658 5695 5732 5769 5806 5843 5880 5917
vtxtable band 6 LOWRACE L FACTORY 5333 5373 5413 5453 5493 5533 5573 5613
vtxtable powerlevels 5
vtxtable powervalues 10 2 14 20 26
vtxtable powerlabels 0 RCE 25 100 400
Brand Name: Happymodel
Item Name: Mobula7 HD 2-3S 75mm Brushless whoop drone
Weight: 48g(without battery)
Weight:72g(with Original 3s 300mah Lipo battery )
New Crazybee F4 PRO V3.0 AIO Flight controller 2-3s Lipo Compatible
2S for indoor Cine whoop mode
3S for outdoor Freestyle whoop mode
Betaflight support , multi flight mode: ACRO/AIR/ANGLE
The lightest 1102 brushless motor only 2.7g with double ball bearings
Powerful and smoothly
Betaflight OSD support ,easy to get RSSI, Voltage ,current from your goggles(DSMX version no RSSI output)
Runcam Split3-lite 1080p 60fps DVR ready
Camera Angle adjustable
VTX power switchable 25mw~200mw
Smartaudio ready , change VTX bands, powers, channels via OSD
Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible
Flysky version support both AFHDS and AFHDS-2A protocol transmitter
DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter
No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS etc..
Full telemetry function ready (Frsky Non-EU and Flysky version support)
Special Breath light ready
Real Bind and Fly version
Compatible both for 2s-3s Lipo/LIHV
|Mobula7 V3 Frame||1|
|Option1: Crazybee F4FR V3.0 PRO FC built-in Frsky NON-EU RX||1|
|Option2: Crazybee F4FS V3.0 PRO FC built-in Flysky RX|
|Option3: Crazybee F4 V3.0 PRO FC with external DSM2/DSMX RX|
|Option4: Crazybee F4 V3.0 PRO FC no RX verion|
|EX1102 KV9000 Motor||4|
|Runcam Split3-lite+1080p 60fps DVR||1|
|5.8G 40ch 25mw-200mw VTX||1|
|3S 11.4v 300mah 30C/60C battery||1|
|Propeller disassemble tool||1|
Spare parts specifications:
|Motor||Mode: EX1102 KV9000
|Flight controller||(Frsky version) CRAZYBEE F4FR PRO V3.0 Firmware target: CrazybeeF4FR
(Flysky version) CRAZYBEE F4FS PRO V3.0 Firmware target: CrazybeeF4FS
(DSM2/DSMX version) CRAZYBEE F4 PRO V3.0 Firmware target: CrazybeeF4DX
(No RX version) CRAZYBEE F4 PRO V3.0 Firmware target: CrazybeeF4DX
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 2-3S battery input (DC 7.4V-13V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable)
Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable)
DSM2/X Version comes with external DSM2/DSMX compatible satellite receiver
No RX version need to add external Receiver
Built-in Betaflight OSD(SPI Control)
Built-in Current meter Max 28A
Current meter scale set to 470
Built-in 5V 1A Buck / Boost with LC filter
Built-in voltage detection
|Onboard 4in1 ESC||MCU upgraded to EFM8BB21
Power supply: 1-3S LiPo/LiPo HV (3.5v/13v)
Current: 5A continuous peak 6A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.Hex
Default protocol: DSHOT600
|Frsky NON-EU receiver Version||SPI BUS receiver
Frsky D8/D16 switchable
Compatible Non EU transmitter both D8 and D16 mode
Channels: 8ch or 16ch
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
|Flysky receiver Version||SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
|Speki+ DSM2/DSMX receiver version||Brand: Happymodel
Model Name: Speki+
Support protocol: DSM2/DSMX
Output Signal configuration: SRXL(Set Spektrum2048/SRXL for the serial receiver provider)
Antenna connector: I-PEX MHF3
Antenna length: 70mm
Input voltage: 3.6v~13v
Input current: 100ma
Channels: Max12ch(usually channel 12 is used for RSSI)
For the radio transmitter which come with Opentx and equipped with DSM2/DSMX module, the RSSI display as the value of Hold from the radio screen. And the input voltage is display as the value of A2 .
Output Power(telemetry): 18dBm
|PNP No RX version||No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS etc.|
|VTX||Output power: 25~200mw switchable
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Antenna: RG178 antenna
Frequency: 5.8GHz 5bands 40 channels
With RacebandSmartaudio ready
|Runcam Splite3-lite||Brand: Runcam
Field of View(FOV):Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video File Format: MOV
Image Resolution:2 MP
TV Mode: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Max Micro SD Card Supported 64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III)
Hole Distance of Installation: 25.5*25.5mm
PCB Size: 29*29mm
Lens Module Size: 14*14mm
Lens Specs: M9
Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.)
Working Current: 450mA @5V
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Weight: 23gConnector: XT30
I have a mobula hd pre ordered and just want to verify the prop shaft size. Is it 1mm or 1.5mm?
I want to order some spare props and need to know before hand.
Thanks and can’t wait to fly this baby!!
Hello , it’s 1mm
Hello jason, when the mob7 hd runcam split3 available on the market? Where i can buy it?
Are you going sell any 3s batteries for the hd
Are you sure its 1mm. 1100 series motors are typically 1.5mm shaft?
The motor for Mobula7 HD is 1mm shaft
thanks for confirming. much appreciated
I ordered the wrong spare props then as I assumed it would be 1.5 shafts like most others.
Will there be an EU-LBT compatible version?
I would also like the non-LBT version.
I preordered the HD mobula beginning of February on RaceDayQuads website. They said the release day was going to be mid to end of February. Its mid March already and still no delivery info from them. They keep saying they ordered them , but all they can do is wait. Do you have a solid release date?
I purchased the Modular 7 HD when it first became available for pre-order. I finally received it last Friday. First flight I had to use turtle mode. After it flipped over it wouldn’t fly anymore. That was because a prop flew off. Somehow it damageded the wiring going from the DVR to the camera. Do you know if that is something that can be purchased? I’ve googled but had no luck. The company I purchased it from States they’re waiting for you to get back to them on the cable that goes between the two.
Can i use GNB HV4.35v 520mah 2S1P 7.6v 3.95wh batteries? They same size as your 3S. This only have more mah.
Is this drone : Mobula7 HD 2-3S compatible brushless HDwhoop Cinewhoop
Compatible with FRSky ACCESS protocol? I have a FRSky HORUS X10S working with ACCESS.
I think everything posted made a lot of sense. However, what
about this? suppose you were to create a killer title?
I am not suggesting your information is not solid, however suppose you added a post title that makes people desire more?
I mean Mobula7 HD 2-3S compatible brushless HDwhoop Cinewhoop – Happymodel is a little vanilla.
You ought to peek at Yahoo’s front page and
note how they create post titles to get people to open the links.
You might add a video or a picture or two to get people interested about
what you’ve written. Just my opinion, it could make your posts
a little livelier.
Great blog here! Also your web site quite a bit up fast!
What web host are you the use of? Can I get your
affiliate hyperlink for your host? I want my web site loaded up
as quickly as yours lol
Hello Dear, are you in fact visiting this web page daily, if so
after that you will without doubt obtain pleasant knowledge.
Everyone loves what you guys tend to be up too.
This kind of clever work and reporting! Keep up the good works guys I’ve incorporated you guys to our blogroll.
You are so interesting! I do not suppose I’ve truly read something like this before.
So great to discover somebody with a few genuine thoughts on this subject matter.
Seriously.. thanks for starting this up. This site is
something that is needed on the web, someone with a bit of
Hi, i think that i saw you visited my weblog so i came to “return the favor”.I am trying
to find things to enhance my website!I suppose its ok to use a few of
Hi, I do think this is a great site. I stumbledupon it 😉
I may revisit once again since I bookmarked it. Money and freedom is the greatest way to
change, may you be rich and continue to guide others.
Someone essentially assist to make significantly articles I would
state. This is the very first time I frequented your web page and
thus far? I amazed with the research you made to create this actual post amazing.
Good day! I could have sworn I’ve been to this site before but after reading through some of the post I realized it’s new
to me. Anyhow, I’m definitely glad I found it and I’ll be book-marking
and checking back often!
Hi! Do you use Twitter? I’d like to follow you if that would be okay.
I’m undoubtedly enjoying your blog and look forward to new updates.
I do believe all the ideas you’ve introduced on your post.
They’re really convincing and can certainly work. Nonetheless, the posts are very
short for starters. May you please lengthen them a bit from next time?
Thanks for the post.
When I originally commented I appear to have clicked on the
-Notify me when new comments are added- checkbox and from now on every time a comment is added I
receive 4 emails with the exact same comment. Is
there an easy method you are able to remove me from that service?