Update log: DiamondF4FR V3.2 version already came with Built-in OPENVTX could support max 400mw output. Please use following vtxtable
# vtxtable
vtxtable bands 6
vtxtable channels 8
vtxtable band 1 BOSCAM_A A FACTORY 5865 5845 5825 5805 5785 5765 5745 5725
vtxtable band 2 BOSCAM_B B FACTORY 5733 5752 5771 5790 5809 5828 5847 5866
vtxtable band 3 BOSCAM_E E FACTORY 5705 5685 5665 0 5885 5905 0 0
vtxtable band 4 FATSHARK F FACTORY 5740 5760 5780 5800 5820 5840 5860 5880
vtxtable band 5 RACEBAND R FACTORY 5658 5695 5732 5769 5806 5843 5880 5917
vtxtable band 6 LOWRACE L FACTORY 5333 5373 5413 5453 5493 5533 5573 5613
vtxtable powerlevels 5
vtxtable powervalues 10 2 14 16 26
vtxtable powerlabels 0 RCE 25 100 400
This flight controller is inspire from “Angry Don FPV”
Notes:2.4GHz receiver antenna length change to 5cm since Nov.15th 2021.
| Flight controller | (ELRS SPI RX version)DiamondF4 ELRS FC Firmware target: CrazybeeF4SX1280 (Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR (Flysky SPI RX version)DiamondF4 FS FC Firmware target: CrazybeeF4FS Discontinued MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection) Original whoop size compatible Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G OPEN VTX Built-in SPI ELRS V2.0/Frsky receiver Built-in 5V 1A BEC |
| Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT600 |
| Onboard ELRS V2.0 receiver Version | Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V2.0 RF Frequency: 2.4GHz Antenna : Enameled copper wire antenna Telemetry output Power: <12dBm Receiver protocol: SPI ExpressLRS Compatible with ExpressLRS V2.0 TX Module Couldn’t flash separately ExpressLRS firmware |
| Onboard Frsky SPI D8 receiver Version | SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 modelChannels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m |
| Onboard Flysky SPI receiver Version | SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support |
| Onboard 5.8g OPENVTX | Firmware version: OPENVTX Smartaudio v2.1 PIT Mode support RCE Mode support Channels:48ch Transmitting Power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v): <650ma (400mw) |
What are the differences between the DiamondF4 AIO 5-IN-1 Flight controller V1.0 and v2.1, I ended up with one of each. The receiver range on the v1.0 is not very good, hoping v2.1 is better, haven’t tried it yet.
Thanks
Can I please get the esc hex file for the happymodel diamond f4 aio board? I accidentally reflashed it with the old 16.7 version and I need the
O_H_5_REV16_8.HEX
File.
I can’t find this specific one anywhere!!
Thanks for the help, keep making great products
Hi, could I please get the esc firmware O_H_5_REV16_8.HEX
I can’t find it on your site!
Thanks and keep up the good work!
How to use SmartAudio VTX without SmartPort? FRSKY VERSION
Good day.
Became the owner of the Happymodel DiamondF4 AIO 5-IN-1 Flight controller built-in VTX ESC OSD Receiver. The flight controller did not work for long – about 2 hours and burned out. Video broadcast is missing. There are several questions, if you can help me, I will be very glad.
1.From the beginning, the flight controller was very hot. Is it necessary to use additional cooling when the flight controller is operating?
2. I tried to set up ESC and connected the DSHOT600 protocol with BLHeliSuite – unsuccessfully (((maybe I’m doing something wrong?
Sorry about my English, this is not my native language 🙂
I would be grateful for your feedback.
Hi, Yuriy. Did you solve your problem? I have the same issue with video transmitter.
My VTX also doesn’t seem to output reliably. It works for a bit then cuts out for no reason.
I also just have this issue of no vtx output on any channel. Also had issue going to BF4.3 went back to 3.5.7
I bought this board a few days ago and there is no indication what orientation is up and forward. can I assume USB is up and the camera is forward?
Can i use DJT transmitter with Frsky D8 version?
My DiamondF4 AIO did not come with an antenna wire. What is the proper length of wire needed?
Hello, I received the elrs version of this and the video does not work. the OSD works. I have a known good camera connected to it. any help would be great.
Hello. I purchased ELRS version, get it working and flying, but after two days it is not working anymore. When USB is connected then it seems dead. When I connect battery then I can hear first 3 beeps and no LED light. This was very strange experience. Is there any option to get it working?