V2.0 update log: Changed to GNB27 connector and V4 frame, no need 3d print battery tray anymore. And changed the propeller to Gemfan 1635-3 propellers.
Specifications:
Brand Name: Happymodel
Model: Moblite7 Walksnail
Frame wheelbase: 75mm
Weight: 33.5 gram without battery
Size: 98mm*98mm*48mm
Receiver option:
SPI ELRS 2.4GHz
SPI FRSKY 2.4GHz
Compatible with 1S Lipo battery or Lihv battery
Battery Plug: GNB27
Package includes:
| Item Name | Qty |
| Mobula7 v4 75mm frame +Canopy | 1 |
| SPI Receiver Option1: SuperbeeF4 Lite FC built-in ExpressLRS SPI RX | 1 |
| SPI Receiver Option2: SuperbeeF4 Lite FC built-in Frsky SPI RX | |
| RS1002 KV20000 Unibell brushless motor | 4 |
| Gemfan 1635-3 tri-blades propeller(4cw+4ccw) | 1 |
| Walksnail Avatar nano HD camera | 1 |
| Walksnail Avatar mini 1s tx module | 1 |
| Spare Canopy | 1 |
| Propeller disassemble tool | 1 |
| Screw driver | 1 |
| GNB27 to PH2.0 convertor wire | 1 |
*The FPV goggle in the picture is for display only and is not included in the delivery package
| Flight controller
SuperbeeF4 Lite ELRS/FRSKY |
SPI ELRS version Firmware target: CrazybeeF4SX1280SPI FRSKY version Firmware target: CrazybeeF4FR MCU:STM32F411CEU6 (100MHz, 512K FLASH) Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection) Power supply: 1S Lipo Lihv battery input (DC 2.8V~4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot300 ready Built-in Betaflight OSD(SPI Control) Built-in SPI Frsky/ExpressLRS receiver Built-in 5V 1A BEC Built-in voltage detection |
| Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV (2.8v~4.35v) Currents: 5A continuous peak 6A (5 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT150/DSHOT300/DSHOT600 |
| Onboard SPI ExpressLRS 2.4GHz Receiver | Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz RF Frequency: 2.4GHz Telemetry output Power: <12dBmReceiver protocol: SPI ExpressLRS Could bind with ELRS V2.0 firmware TX module Also support ELRS V3.0 , need upgrade betaflight firmware |
| Onboard Frsky SPI D8 /D16 2.4GHz Receiver | SPI BUS receiver Frsky D8/D16 compatible Compatible Non EU transmitter D8 model and EU-LBT(Frsky_x_lbt)Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m Based on CC2500 RF module Compatible with Futaba S-FHSS , Redpine protocol |
| Motor | Model: RS1002 20000KV Configu-ration:9N12P Stator Diameter:10mm Stator Length:2mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ13.5mm*12.5mm Weight(g):2.5g No.of Cells(Lipo):1S only |
| Propeller Gemfan 1635-3 Bi-blades | Props Dia:40mm Shaft size:1.5mm Include 4pcs a pack |
| VTX | Model: Avatar mini 1s VTX V2.0 Communication Frequency: 5.725-5.850 GHz Transmitter Power(EIRP): FCC:<25.5dBm; CE:<14dBm; SRRC: <20dBm;MIC:<25dBm l/o Interface: JST1.O*6(Power in)JST1.O*4(USB) Mounting Holes: 25.5*25.5 mm Dimensions: 30*30*6.5 mm Storage: 8G Recording: 1080p/720p Weight: 6.8 g Operating Temperature: -20-40℃ Channels: 8 Wide Power lnput: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps / 50mbps Latency: Average delay 22ms Antenna connector: IPEX |
| Camera | Model: Avatar nano lmage Sensor: 1/2.7”Inch Resolution: 1080P/6Ofps,720P/120fps,72OP/6Ofps Ratio: 16/9 4/3 Lens: 2.1mm FOV 170° Aperture: F2.0 Shutter: Rolling shutter Min.Illumination: 0.001Lux Weight: 3.5g Dimensions: 14*14*17mm Coaxial Cable: 45mm |
